Configuring LACP Deployments Parent topic

You can open the Deployment Wizard screen after the appliance is configured and modify deployment mode settings for deployments using LACP.
As part of the configuration, you can enable LACP and use trunked interfaces for data ingress and data egress. To deploy LACP link aggregation for Transparent Bridge or Transparent HA modes, the appliance must be equipped with two bypass cards. You must configure the connected switches with the corresponding LACP configuration.
See How LACP Works With Deep Discovery Web Inspector.
Important
Important
Keep the following in mind if configuring Transparent HA mode with LACP:
Configuration and policy settings are synchronized between the two Deep Discovery Web Inspector HA nodes. This synchronization is not implemented by the Deep Discovery Web Inspector itself, but by the Deep Discovery Director appliance to which the Deep Discovery Web Inspector nodes are registered. The synchronization is accomplished by configuring the Deep Discovery Director synchronization scheduling task.
Therefore, to implement a Transparent HA mode deployment, you must integrate and register each of the Deep Discovery Web Inspector HA nodes to Deep Discovery Director.
Note
Note
You can exit the Deployment Wizard at any time by clicking on another menu item in the management console. If you exit the wizard before finishing the configuration process, all data entered will be lost.
If you are performing the initial deployment, see Deployment.

Procedure

  1. Go to Administration → Deployment Wizard.
    The Welcome page opens.
  2. In the Deployment Mode section, select Transparent bridge or Transparent HA according to your business needs.
  3. Click Next.
  4. In the Working Mode Settings page, specify the following:
    Option
    Description
    HTTP port
    Scan for HTTP traffic on this port. Default is 80.
    HTTPS port
    Scan for HTTPS traffic on this port. Default is 443.
  5. Click Next.
  6. In the Network page, specify the following details:
    Option
    Description
    Host name
    Specify a host name.
    Primary DNS server
    Specify the IP address of the DNS server. This is a required setting.
    Secondary DNS server
    Optionally, specify the IP address for a secondary DNS server.
    Enable LACP
    This configuration field only appears when the device is configured with two bypass cards.
    Enable LACP.
    Interfaces eth4/eth6 and eth5/eth7 will be teamed to become team0 and team1 respectively.
    LACP bond interface
    This option is visible only if LACP is enabled.
    A read-only field, preset to eth4/eth5/eth6/eth7.
    Data ingress / egress interface
    When LACP is enabled, this is a read-only field that is pre-set to team0/team1.
    Data interface
    Appears only under Transparent HA mode. This is a read-only field and is pre-set to br0.
    Enable VLAN ID
    Appears only under Transparent HA mode. Configuration is based on requirements.
    IPv4 address, IPv4 mask, and IPv4 gateway
    Appears only under Transparent HA mode. Configuration is based on requirements.
    Management interface
    This is a read-only field and is pre-set to eth0.
    Mode
    This is a read-only field and is pre-set to static.
    IPv4 address, IPv4 mask, and Default IPv4 gateway
    Specify the IPv4 network settings for the management interface.
  7. Click Next.
    The Time page opens.
  8. In the Time section, configure the time and location settings for the Deep Discovery Web Inspector appliance.
    Option
    Description
    NTP server
    Enter the NTP server IP address.
    System time zone
    Set the appropriate time zone by selecting the location closest to the Deep Discovery Web Inspector appliance.
    Optionally, instead of selecting a location, you can select Etc and then choose the offset that matches the location closest to the Deep Discovery Web Inspector appliance.
  9. Click Next.
    The Summary page opens.
  10. Review and verify the settings and then perform the appropriate action:
    1. If the settings are not as desired, click on Previous and modify settings as required.
    2. If the settings are verified, click on Done to save the configuration.
      Note
      Note
      After you click Done, a dialog box opens asking if you want to reboot the appliance. After you click OK, the connection to the appliance disconnects and the appliance reboots. After the appliance restarts, the Log On page is displayed.
      If you do not want to reboot, you can click Cancel instead of OK. If you click Cancel, the Summary page reopens.
    Important
    Important
    If you exit the wizard before saving settings, the configuration is not saved.

Related information