Private Access Connector CLI Commands

A list of available CLI commands for managing the Private Access Connector virtual appliance.

To access the CLI, connect to and open the Connector virtual appliance (either directly or through SSH). Log on to the CLI with your account credentials.

To view basic information of the Private Access Connector, such as network settings and service status, run the show command. For example, use show ip route to check the network IP route. For a list of available commands, type show and then press the ? key.

To view a list of tasks you can perform and enable administrative commands, run the enable command. Enabling administrative commands changes the command prompt from > to #.

The following table lists out the administrative commands you can use to manage the Connector virtual appliance.

Command

Syntax

Description

enable

enable

Enter privileged mode to enable administrative commands

clear

clear

Clear the content on the screen

exit

exit

Exit the session

reboot

reboot

Restart a Private Access Connector immediately

shutdown

shutdown

Shut down a Private Access Connector immediately

passwd

passwd

Change the password of running the enable command

register

register <registration_token>

Register a Private Access Connector to Trend Micro Vision One

unregister

unregister

Unregister a Private Access Connector from Trend Micro Vision One

unregister force

unregister force

Forcibly unregister a Private Access Connector from Trend Micro Vision One

ifconfig

ifconfig

Show information about an interface

ping

ping [-c num_echos] [-i interval] <dest>

Check the connection to a destination

[num_echos]: Number of echo requests to be sent

[-i interval]: Delay interval in seconds between each packet

<dest>: Destination host name or IP address

traceroute

traceroute <dest>

Track route to a destination

<dest>: Destination host name or IP address

resolve

resolve <dest>

Reslove an IP address from a host name or resolve a host name from an IP address

<dest>: Destination host name or IP address

show interface

show interface

Display information about all interfaces in use

show dpid bypass

show dpid bypass

Display whether the rule enforcement function of a Private Access Connector is disabled

show dns

show dns

Display the DNS settings of a Private Access Connector

show hostname

show hostname

Display the host name of a Private Access Connector

show uptime

show uptime

Display the time when a Private Access Connector is up and running, as well as its load information

show version

show version

Display the version of a Private Access Connector

show ip route

show ip route

Display the routing table of a router

show register

show register

Display the registration status of a Private Access Connector

show timezone

show timezone

Display the time zone of a Private Access Connector

configure interface ip

configure interface <interface> <ip> <mask>

Configure the IP address for the eth0 interface

<interface>: eth0

<ip>: IP address for the interface

<mask>: Network mask for the interface

configure hostname

configure hostname <hostname>

Configure the host name for a Private Access Connector

<hostname>: Host name or FQDN for the Connector

configure primary dns

configure dns primary <dns>

Configure a DNS server as the primary DNS server

<dns>: IP address of a DNS server

configure secondary dns

configure dns secondary <dns>

Configure a DNS server as the secondary DNS server

<dns>: IP address of a DNS server

configure no dns primary

configure no dns primary

Delete the primary DNS server

configure no dns secondary

configure no dns secondary

Delete the secondary DNS server

configure ip route

configure ip route <dest> <via>

Add a static route entry for traffic to any destination

<dest>: 0.0.0.0/0

<via>: IP address of the default gateway

configure no ip route

configure no ip route <dest> <via>

Delete the static route entry for traffic to any destination

<dest>: 0.0.0.0/0

<via>: IP address of the default gateway

configure dpid bypass

configure dpid bypass <on/off>

Disable or enable the rule enforcement function of a Private Access Connector

If <on/off> is set to on, the Connector does not enforce rules to user access requests and allows all access to destinations. The default value is off.

configure ping

configure ping <interface> <on/off>

Allow or block ping packages for the eth0 interface

<interface>: eth0

configure ssh

configure ssh <interface> <on/off>

Allow or block ssh traffic for the eth0 interface

<interface>: eth0

configure dhcp

configure dhcp <interface>

Configure the DHCP mode for the eth0 interface

<interface>: eth0

configure timezone

configure timezone <timezone>

Configure the time zone for a Private Access Connector

Options for <timezone> include:

  • <region>/<city>: Sets the time zone in region/city format, for example, Asia/Shanghai

  • UTC: Sets the time zone to UTC time